Ahuja-Orlin

General Information

Algorithmic problem: Max-Flow Problems

Type of algorithm: loop

Abstract View

Invariant: After [math]\displaystyle{ i \ge 0 }[/math] iterations:

1. The flow [math]\displaystyle{ f }[/math] is a fleasible flow.
2. If all upper bounds are integral, [math]\displaystyle{ f }[/math] is integral as well.
3. There is a valid distance labeling [math]\displaystyle{ d }[/math] with respect to [math]\displaystyle{ f }[/math].
4. Each node [math]\displaystyle{ v\in V\setminus\{t\} }[/math] has a current arc, which is either void or one of the outgoing arcs of [math]\displaystyle{ v }[/math].
5. Stack [math]\displaystyle{ S }[/math] contains a current flow-augmenting path with respect to [math]\displaystyle{ f }[/math]. This path starts with [math]\displaystyle{ s }[/math] and ends at an arbitrary node of [math]\displaystyle{ G }[/math]. Each arc on this path is admissible and the current arc of its tail node.

Variant: Exactly one of the following actions will take place in the current iteration:

1. An arc is appended to the current path.
2. At least one arc is saturated.
3. The distance label of some node is increased.

Break condition: [math]\displaystyle{ d(s)\geq n }[/math], where [math]\displaystyle{ n=|V| }[/math],

Induction basis

Abstract view:

1. We start with some feasible flow, for example, the zero flow.
2. For each [math]\displaystyle{ v\in V }[/math], [math]\displaystyle{ d(v) }[/math] is initialized to be the smallest number of arcs from [math]\displaystyle{ v }[/math] to [math]\displaystyle{ t }[/math].
3. Stack [math]\displaystyle{ S }[/math] is initialized so as to contain [math]\displaystyle{ s }[/math] and no other node.
4. The current arc of each node [math]\displaystyle{ v\in V }[/math] is reset to be the very first outgoing arc of [math]\displaystyle{ v }[/math].

Implementation:

1. For all [math]\displaystyle{ a \in A }[/math], set [math]\displaystyle{ f(a):=0. }[/math]
2. Run a BFS on the transpose of [math]\displaystyle{ G }[/math] with start node [math]\displaystyle{ t }[/math] and unit arc lengths; the resulting distances are the [math]\displaystyle{ d }[/math]-labels.
3. Create [math]\displaystyle{ S }[/math] and push [math]\displaystyle{ s }[/math] onto [math]\displaystyle{ S }[/math].
4. Reset the current arcs.

Proof: Obvious.

Induction step

Abstract view:

1. Let [math]\displaystyle{ v }[/math] be the top element of [math]\displaystyle{ S }[/math], that is, the endnode of the corresponding path.
2. If [math]\displaystyle{ v=t }[/math]:
   1. Augment the current flow along the path correspoding to [math]\displaystyle{ S }[/math].
   2. Remove all nodes but [math]\displaystyle{ s }[/math] from [math]\displaystyle{ S }[/math].
   3. Otherwise:
      1. While the current arc of [math]\displaystyle{ v }[/math] is not void and not admissible and not pointing to a node [math]\displaystyle{ w\ne s/math\gt , move the current arc one step forward. ### If the current arc is void: Set \lt math\gt d(v):=\tilde{d}+1 }[/math], where [math]\displaystyle{ \tilde{d} }[/math] denotes the minimum value [math]\displaystyle{ d(w) }[/math] over all outgoing arcs [math]\displaystyle{ (v,w) }[/math] of [math]\displaystyle{ v }[/math] in the residual network.
      2. Otherwise, that is, if the current arc is some arc [math]\displaystyle{ (v,w) }[/math]: Push [math]\displaystyle{ w }[/math] on [math]\displaystyle{ S }[/math].

Proof: The variant and points 1, 2, and 4 are obvious. For point 5, note that step 2.3.1 skips all non-admissible arcs, so step 2.3.3 is only applied to admissible arcs. Finally, point 3 of the invariant follows from the maximally conservative increase of [math]\displaystyle{ d(v) }[/math] in step 2.3.2.

Complexity

First we show that no distance label [math]\displaystyle{ d(v) }[/math] may become higher than [math]\displaystyle{ n }[/math]. To see that, recall [math]\displaystyle{ d(s)\lt n }[/math] from the break condition. Whenever the distance label [math]\displaystyle{ d(v) }[/math] of a node [math]\displaystyle{ v\in V }[/math] is increased, [math]\displaystyle{ v }[/math] is the endnode of the current path, which consists solely of admissible arcs. Due to the definition of admissible arcs, it is [math]\displaystyle{ d(v)\leq d(s) }[/math] immediately before the current iteration (equality only if [math]\displaystyle{ v=s }[/math]). Let [math]\displaystyle{ (v,w) }[/math] be an arc such that [math]\displaystyle{ \tilde{d}=d(w) }[/math]. For the same reason, it is [math]\displaystyle{ d(w)\lt d(s) }[/math], which implies [math]\displaystyle{ d(v)\leq d(s) }[/math] immediately after the current iteration.

Remark

This algorithm may be seen as a "lazy" variant on Edmonds-Karp. In fact, the most expensive step there is the computation of a flow-augmenting [math]\displaystyle{ (s,t) }[/math]-path. This task amounts to computing the true distance from every node to [math]\displaystyle{ t }[/math]. A valid distance labeling may be seen as "lazily evaluated" true distances.